Cat flaps allow your pet leave and come whenever they want, without you needing to let them in or out. They also can help stop your cat from peeing in the home.

Fitting a cat flap in a upvc door panel is much simpler than installing one in glass doors, however it does require some skills and the appropriate tools.

Measure the Door

fitting cat flap in upvc door panel a cat flap in a door can be tricky but as long as you choose the right type of cat flap be patient and follow the directions provided, it shouldn't be a problem. We will show you how to draw the shape, then use a jigsaw to cut out the door's opening and then finish off the job by attaching the cat flap to the door. This will ensure that the flap stays in place and protects the door from wind and rain damaging the door.

The first step is take a measurement of the width of your pet to get a precise measurement of what size of cat flap you will require. This will ensure that the flap is big enough to let your pet enter and leave the house without needing to open and close the door each time, but it is also small enough to keep them from moving too far in either direction.

If your kit has an illustration of where to drill, then stick it on the door and then draw around it. If your door has sill or moulding on the bottom of it ensure you have enough space to keep your cat safe and will prevent them from getting access to your home.

Put on your eye protection as well as a dust mask. Then using a jigsaw, begin to cut along the line you penciled in. Don't push the blade too hard, as this will cause it to cut more quickly than you would like it to. If you have a square that you have cut, use it to ensure that you're cutting properly and to make sure the hole is a good rectangle. Once you are satisfied with this you can begin to take off the remaining door material.

Draw a Line

The cat flap is a great way to allow your pet to go in and out without having to worry about them coming in with a visitor, or leaving unwanted gifts in the house. It also stops draughts and keeps your home's temperature in check. Installing a cat flap on your door may seem daunting to those who haven't done it before. Many people will call an expert carpenter or joiner to complete the work. While this is definitely an option, it's possible to do the job yourself if you own the appropriate tools and follow the instructions with care.

It is much easier to accomplish on wooden doors, but it is still possible using upvc door panel replacement cat flap. However, you must be careful not to harm the doors since this could make it impossible to claim your warranty. First, you need to measure the door to ensure that it can accommodate the new cat-flap. This should be simple enough if you are using the standard uPVC door, but you may require extra care if you are using a composite or other kind of door, as they are more difficult to cut into than solid uPVC panels.

Next, you will need to determine the height of your belly for your cat. This is the distance from the floor to the lower part of the cat's stomach, and you'll need to find a place in the door where this measurement is within the range that your cat can comfortably pass through. Once you've figured out the measurements you'll need to mark the area with a spirit level and a pencil so that you are certain that the hole will be suitable for your cat flap fitting.

After you have marked the area, you're now ready to cut the hole. You will need an jigsaw. It is essential to take your time to ensure that the cuts are smooth and clean rather than uneven and rough, as it could cause damage to your door. You should also remember to wear safety glasses and a dust mask whenever working with the jigsaw as breathing in the dust can be dangerous to your health. After you've finished the cutting, you will have to smooth out the edges of the hole using sandpaper, so that the cat flap can be fitted easily into place.

Cut a Hole

It can be a challenge to fit an animal flap on a door panel or a sealed double glazing unit. If you are not very experienced in DIY, it's best to hire an expert to do the job for you. A shoddy job might not only look ugly, but also an enigma for security and also allow cold air to get in when the cat is outside, and hot air to escape when inside.

Mark the hole's position on the door with an eraser and a spirit level. This will ensure it is correctly positioned and runs flush with the door's other parts. You should make sure you have a piece of sandpaper at ready for any rough edges.

After the line is drawn, you can cut the hole with a jigsaw, remember to wear the appropriate safety gear for working with an electric tool. If you're worried about noise, you can purchase a cordless jigsaw which is quieter and more user-friendly.

It is best to only remove the material required to make the flap. A little bit of extra material is required to increase the thickness of the the flap, but cutting off more than this can cause problems and even harm the frame of the door.

A door made of upvc could have a metal frame or panel which could block the microchip cat flap and in this case you'll need to cut an oversize hole so that the metal does not get in contact with the the cat flap, if this is done, it is essential to fill in the gap and seal it with water.

If you're installing a cat flap into the frame of a double glazed windows with a frame made of metal, you'll need to talk to a specialist who can provide you with a new pane of glass with the hole for the cat flap inside. It is much less expensive to have this done than to attempt to fix the cat flap onto an existing glass pane that has not been manufactured specifically for the purpose.

Fit the Flap

Cat flaps give your pet the freedom to move around anytime they want, allowing them to relax in the house when they like. If you have a uPVC front door, it can be difficult to put in a cat flap. This is especially true when you don't have glass panels that is cut. If you're able to purchase and install a half-glazed replacement uPVC panel, then it's possible to add an animal flap onto the doors. It's not a matter of cutting a hole into the door. You'll also need to do a few things to ensure that it is secure.

A upvc door panel replacement cat flap, GRP or composite door panel is typically made up of an flimsy plastic outer layer joined to a soft insulating polystyrene core. The material is extremely fragile and care must be taken when cutting into it to avoid damaging. This type of door has a template you can use to make the hole.

After you've marked the location of the hole in your door, it's time to fit the cat flap itself. You can buy and fit many different models that range from simple button operated ones to ones that are activated by microchips that allow only your pet. However, regardless of what kind of cat flap you pick, it's important to make sure that your cat can use the flap without becoming trapped outside in bad weather.

A circular fitting is better than a square because circles can be cut more securely into the glass. This is because square holes make the glass more susceptible to cracking when a drill is used on it. It's also a safer choice to use since you're not putting yourself at risk by having to drill into toughened glass that may break and hurt your pet or your family. This is particularly important if you have young or elderly person in your home who could be injured by shards glass.