Replacement UPVC Door Handles

Find the perfect handle for your door, whether you are replacing your handles or adding security. These upvc handle are easy to install and have the minimum 92mm center distance of multipoint locks.

The most important measurements to consider are backplate fixing centres as well as key hole dimensions for levers and levers. Check these carefully against your existing measurements prior to placing an order.

Lever/Pad

Lever pad handles are made up of a lever on one side, and a paddle-shaped handle on the opposite. They are designed to be used with key wind locks although they can also be adapted to multipoint split spindle door locks (though you'll need an additional dual spindle lock case).

Once you have selected the appropriate handle for the doors, the finishes will be listed in the drop-down menu. Some styles of handles are not available in all finishes. It is recommended to check the technical drawing and dimensions for the item you are looking to ensure you get the right fit and size.

It is crucial that when selecting a new set upvc lever pad handles, they match the PZ (distance from the spindle of the handle to the centre of the hole of the cylinder) of your multipoint door locks. This is because these must be lined up for the doors to stay locked, no matter if you're looking from the inside or outside. Our handles are designed to fit the majority of standard cylinders, however it is a good idea to double-check before ordering.

If you wish to upgrade to dual spindle levers you'll need to take out the window handles for wooden windows you have already installed and disassemble the lock case. This will require an additional split inline cylinder. You can purchase these separately. We have included a technical illustration in the images of each product.

Once you have removed the screws holding the handle on your door, it is recommended to loosen them and inspect the mechanism to determine the condition it is in. You may need to loosen the screws a bit more if they are not tight. After that, you can take off the old handle and spindle and replace it with a new victorian door Handle handle made of upvc. Before screwing the handle into the frame, it is a good idea to make sure it is in the proper position, and you can do this by placing your finger into the gap between the door frame and the door handle to make sure that it is in a level position.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock that uses a Euro cylinder. They can be found on a variety of double upvc doors as well as some aluminium and wooden doors. They are equipped with a lever on the inside and an outside paddle and are generally available in two types. Sprung - These have a spring cassette installed within the backplate, which helps bring the handle lever into a horizontal position. Non-sprung - These do not have a spring mechanism and will need to be manually pulled to raise the handle lever to the horizontal position.

To fix a sagging lever door handle, you will need to find the hole for access to the detent or pin, which is typically a small rectangle or round shape hole or protruding pin situated on one side of the base plate. Once you have located it, loosen the set screw using the help of a screwdriver, and then take it off to allow the lever and return it to the horizontal position.

When the handle is in a horizontal position you can re-install the screws and tighten them to make sure the handle remains fixed to the base plate. Consider applying a threadlocking solution to the threads of the screw to increase grip and stop them from loosening over time.

Drooping lever door handles could be the result of a number of factors. The most common reason is that the fixings have been over tightened and are putting strain on the bearings of the lever, and causing it to pull against the door face. It could also be that the levers have not been adjusted at the right angle, which stretches the latch mechanism and stops it from fully springing into motion.

Another common reason is that the sprung lever is not functioning properly and this is typically due to the spring not being in the proper position within the backplate. To determine if the handle returns to its horizontal position, simply turn it.

It is important to fix any door handles that are loose as soon as possible. This could lead to excessive wear on the screws, and the handle could fall off the base plate. It is also a good idea to tighten all loose screws on a regular basis, as this will help to prevent them from loosening.

Lever/Snib

These handles made of upvc are also known as 'Snib' handle sets and have a snib lever on the top of the lever that can be pressed down to lock your door if you don't use the Dummy lock. They usually come with a Fullex 68PZ (that's 68mm between the spindle's center and lever or the lock centre) door lock. We also have a selection of 68PZ door handle from manufacturers such as Ferco and Fab & Fix.

Changing your door handle is an inexpensive method to upgrade your home, whether you're replacing your handles or installing new ones to doors you've built in your house. There are a variety of door handles made of upvc with traditional levers on backplate, straight or curving short latches, and knob handles that resemble dummy knobs for multi-point locks, that are perfect for French doors.

Rose door handles are circular or oval-shaped versions of lever-on-backplate handles. These kinds of door handles are equipped with a lever or knob on a backplate which is placed behind the knob or lever and is sometimes referred to as a rosette, although some back plates can be detached to be concealed for fixing.

There are a wide range of chrome and colored finishes available for these handles that complement your door and other hardware, like bolts, knobs and hinges. Some handles come with grub screws that help firmly attach the lever or knob to the spindle. Some handles come with bathroom spindles, which can be used to make bathroom locks. They also have a thumbturn release mechanism, and can be used on bathroom doors.

Mortise

If your upvc door locks and handles front door handle is stuck in the open position, the reason is likely to be due to the tubular latch. There may be a few reasons for this, one of which is a simple lack of lubrication on the latch plate. It is possible to solve this issue by opening the door and spraying lubricant onto the handle and locking window handles. Or, it could be that the latch plate has been dislodged from the backplate. This is a more complicated issue that requires an expert.

A multipoint handle system is the best solution for stuck door handles. The handles are positioned through the faceplate, and are operated by the use of a key or thumb turn knob that triggers the cam that locks the deadbolt. The handles come in a variety of sizes to suit different kinds of upvc window locking handles doors and are available in various attractive finishes that complement the hardware that is currently in use. These handles can be purchased online or through an authorized locksmith in your area. They are easy to install with clear instructions.

To choose a replacement handle set, you'll have to be aware of the PZ size of your cylinder. This is the distance from the edge of the door frame to the centre point of the handle hole in millimetres. You will also need to know if your door has a hook style lock or a mortise lock. Once you have these measurements, the easiest way to find the correct handles is to search by brand option on the website. This will help you narrow down your options, and then you'll be able to select the right size.

A typical set of handles includes an arm, two screws of different lengths, drill guides, and instructions for installation. Smarter versions, such as the Igloohome Smart Mortise 2+ include a mortice lock with keypad. These are more complex devices that are for professional installers or highly skilled DIYers. Certain handle sets come with a variety of accessories, including weather strips that can be used to enhance the appearance of the door.