Replacement UPVC Door Handles

If you're replacing the handles or need to add extra security you can choose the perfect handle for your door. These upvc handle are easy to install and will meet the minimum 92mm central distance for multipoint locks.

The backplate's fixing centre as well as the dimensions of the lever/keyhole are the most important measurements. Compare these measurements carefully with your existing measurements prior to placing an order.

Lever/Pad

Lever pad door handles repair near me handles are made up of an elongated lever handle on one side and a paddle shaped handle on the other. These are designed for use with key wind locks. However, they can be fitted to multipoint split spindle door locks.

Our range of upvc handles lever pads are available in a wide range of finishes. They will be shown in the drop-down list once you have found the right handle for your door. Not all styles of handles are available in every finish though and you should always look over the sizes and technical drawings for the specific product you're looking for to ensure that you are getting the correct size and fitting.

When selecting the new set of upvc lever pad door handles it is important to ensure that they are in line with the PZ (distance between the spindle of the handle and the center of the hole for the cylinder) of your existing multipoint door locks, as they need to be in line for the doors to remain locked, whether from the inside or outside. The handles we offer are designed to work with a variety of standard cylinder locks, however you should always double-check before purchasing.

If you wish to upgrade to dual spindle levers, you'll need to remove the existing handles and disassemble the lock case. This will require an extra split inline cylinder. These are available separately, and we provide an entire technical diagram that you can look at in the images for each product.

It is a good idea to loosen the screws holding the door handle you have and then inspect the mechanism. It is possible that you will need to loosen the screws further when they aren't tight, and then you can remove the spindle and handle and replace it with a new door handle made of upvc. Before putting the handle in the frame, it is a good idea to make sure it is in the correct place. You can do this by inserting your finger into the gap between the frame of the door and the handle to ensure that it is level.

Lever/Lever

Lever door handles are a multi point lock using the Euro cylinder and can be found on most double doors made of aluminium, upvc door handle repairs doors, and some wooden doors. They feature a lever inside and a paddle on the outside and are generally available in two types. Sprung - They have an internal spring cassette within the backplate that helps to bring the handle lever into an upright position. Non-sprung: They do not include a mechanism that can spring the handle lever into a horizontal position.

To fix a door handle lever that is sagging you'll need to locate the hole or pin that is the detent access point. It's typically a small hole or protruding ring or rectangular located on the handle base plate. Once you have located the detent access hole or pin, you can remove it using a screwdriver.

After the handle is placed horizontally, you can install the screws. Close them to ensure that the handle is securely fixed to the base plate. You may want to apply a threadlocking solution to the screw threads in order to increase grip and prevent them from loosing over time.

Lever door handles that droop could be the result of many factors. The most common cause is that the fixings are too tight and the lever bearing to pull against the door. It is also possible that the levers may not have been operated at a right angle, which compresses the latch mechanism, preventing it from fully springing into operation.

Another common cause is that the lever that is sprung is not operating correctly and this is usually due to the sprung not being in the proper position within the backplate. To check whether the handle is back to horizontal, simply move it.

If the door handles aren't tight, it is important to identify the issue fast, as this can lead to excessive wear on the screws, and even to the handle falling off of the base plate. You should also tighten any loose screws regularly to prevent them from becoming looser.

Lever/Snib

These upvc repair door handle handles are also known as 'Snib' handles and have a snib lever at the top of the lever that you can push down to lock your door in the event that you don't have the Dummy lock. These handles are fitted with a Fullex lock 68PZ. (68mm between the spindle and the lock centre). We also have a range of other door handles with 68PZ from manufacturers like Ferco and Fab & Fix.

You can upgrade your home by changing the handles on your doors regardless of whether you're replacing existing handles or installing new ones on doors you've constructed. There are a variety of upvc door handle available with traditional levers on backplates, straight or curved short latch and knob handles with dummy handles for multi point locks which are perfect for French doors.

Rose Door Lock Handle Repair handles are circular or oval-shaped versions of lever on backplate handles. These door handles are characterized by a lever or a knob that is attached to the backplate. The backplate can be removed for hidden fixing.

There's a wide selection of chrome and colored finishes available for these handles that enhance your door and hardware, including bolts, door lock handle repair knobs and hinges. Some handles are supplied with grub screws, which help firmly attach the lever or knob to the spindle. Other handles are supplied with bathroom spindles that can be used to operate bathroom locks. They incorporate a thumbturn turn and release mechanism, ideal to use on doors for bathrooms.

Mortise

The tubular latch is the most likely to be the cause of this in the event that your door handle is stuck open. This could be due to many things but the most prevalent is a lack of lubrication in the latch plate. This can be resolved easily by opening the door and spraying lubricant onto the lock and door lock handle repair handle. It could also be that the latch has come loose from the backplate. This could be more complicated and requires a professional to fix.

A multipoint handle is the best solution for a stuck door handle. These handles are mounted through the faceplate, and are operated by a key or thumb turn knob that triggers the cam that locks the deadbolt. The handles are available in different sizes to fit various types of uPVC doors and are available in various attractive finishes that match the hardware that is currently in use. The handles can be purchased via the internet or from the local locksmith and can be installed with clear instructions.

To choose a replacement handle set, you'll need to know the PZ size of your cylinder. This is the measurement in millimetres between the inside edge of the door frame and the center of the hole in the handle. You will also need the type of lock that is installed on your door, regardless of whether it is a mortise or hook lock. The easiest way to find the right handles once you have the measurements is to use the brand filter on the website. This will help you narrow down your options, and then you'll be able to select the appropriate size.

A typical set of handles includes the handle unit, a pair of different length screws drilling guides, as well as installation instructions. Smarter versions, such as the Igloohome Smart Mortise 2+ come with a mortice lock with keypad. These are more complex models that are best suited to professional installers or highly skilled DIYers. Some handle sets come with various accessories, including weather strips, which can be used to improve the appearance of the door.