Cat flaps allow your pet leave and come as they please without you needing to let them in or out. They also can help to keep your cat from having to go to the bathroom inside the house.

It is easier to install a cat flap on a upvc panel than a glass one but you'll require some knowledge and right tools.

Measure the Door

The installation of a cat flap in the front door is difficult however, provided that the cat flap is the right type and you follow the directions you can make it less difficult. We will be showing you how to draw the shape, using the jigsaw to slice the door's opening and then finish the job by attaching the cat flap to the door. This will ensure that the flap stays in place and shields the door from wind and rain damaging the door.

To determine the size of the cat flap you need, measure your pet's width. This will allow you to select a flap that is large enough to allow your pet to walk into the house and exit without needing to open the door each time.

Once you have the measurements, you can mark where on the door the template should be placed, usually, this is done using an X. However, some kits come with a drawing that shows the location to drill, if yours does, then you can stick it to the door and use a pencil to draw around the door. If your door has moulding or a sill at the bottom, be sure you leave plenty of space between your cat and the moulding or sill.

Next put on your eye protection as well as a dust mask, and using a jigsaw begin cutting along the line that you penciled in. Don't press the blade too hard because this will cause it to cut faster than you want it to. Set the square with a ruler to ensure you are cutting the material properly and that the hole is a rectangle. Once you are satisfied with the result, you can remove the remaining door material.

Draw a Line

The cat flap is a great way to let your pet out and in without having to worry about them being a nuisance to visitors or leaving unwanted gifts in the home. It also stops draughts and helps to keep the temperature inside your home in a stable manner. However, fitting the cat flap to your door might seem like an intimidating task for those who haven't done it before, leading many people to seek out an expert joiner or carpenter to do the job. While this is definitely an option, cat flap in upvc Door Panel it's possible to do the work yourself if you own the right tools and follow the instructions with care.

While this is much simpler to accomplish when using a timber door it is still possible in uPVC doors - although you need to be very careful not to scratch the doors as this will invalidate the warranty. First, you must measure the door to ensure it will accommodate the new cat-flap. If you have a standard uPVC panel it should be a breeze. However, if your door is composite or another type of door, you may have to be more cautious.

The next step is to determine the height of your cat Flap in Upvc door panel's stomach. This is the amount of height between the floor and the bottom of your cat's stomach. It is important to find an area on the door that allows your cat to comfortably pass through. Once you know this, you will have to draw the area with pencil and a spirit level to be sure that the hole you make will be a good fit for your cat.

Once you have marked out the area, it is time to make the hole. It is important to take your time and use a jigsaw ensure the cuts are clean and smooth, not rough and uneven. This could cause damage to your door. Wear safety glasses and a dust mask while using a jigsaw. Inhaling sawdust is dangerous for your health. After you've finished the cutting, you will need to smooth out the edges of the hole using sandpaper so that your cat flap can be fitted easily.

Make a hole

Installing a cat flap to an existing door panel or double glazing cat flap glazing sealed unit can be quite difficult. It is tempting to tackle the task yourself, but unless you have plenty of experience in DIY it is recommended to hire a professional to do the task for you. A shoddy job might not only be unsightly but it could also be a security risk as well as allowing cold air to get in when the cat is outside, and hot air to escape once inside.

Mark the hole position on the door with an eraser and a spirit level. This will ensure that it is properly positioned and is flush with the rest of the door. Make sure to have sandpaper in your possession to smooth any rough edges.

After the line is traced, you must cut the hole using a jigsaw, remember to wear any necessary safety equipment when working with an electric tool. If you are worried about the sound of the jigsaw, you can purchase an electric version that is quieter and simpler to use.

You should only remove the material that is required to fit the cat flap. It is essential to leave some extra material to make the wall thickness of the cat flap fitters near me flap. However cutting off too much material can cause problems or even damage the frame of the door.

If the upvc door is made of metal, or has a frame, it could interfere with the microchip flap. In this situation, you will need to create an over-sized hole to ensure that the metal does not touch the wall of the flap.

If you want to install a cat flap inside windows made of double-glazed or upvc with frames made of metal, you'll need to consult an expert. They will provide you with a new piece of glass with the hole already made for the cat flap. It is cheaper to have this done than to attempt to fix a cat flaps for french doors flap into an existing pane of glass that has not been manufactured specifically for the purpose.

Install the Flap

cat flap fitting flaps allow your pet to come and go whenever they want, allowing them the ability to unwind inside the house whenever they feel like it. If you have a uPVC front door, it might be difficult to put in the cat flap. This is especially true if you do not own glass panels that can be cut. Luckily, if you're happy to purchase and install a half-glazed replacement uPVC panel then it is possible to add an animal flap onto the doors. It's not as simple as just making a hole in the door though and there are some things you'll need to do first to make sure it's safe.

A uPVC, GRP or composite door panel typically comprises a flimsy plastic outer skin joined to a soft polystyrene core that is insulating. The material is quite fragile and care should be taken when cutting into it to avoid damaging. This kind of door comes with a template that you can use to make the hole.

Once you've marked the hole in your front door, it's time to put in the cat flap. You can choose from a variety of models, ranging from simple push-button units to microchip-activated ones that allow only your pet to enter. However, regardless of what type of cat flap you select, it's important to make sure that your cat is able to use the flap and not get trapped in the weather.

It's a good idea choose circular fittings rather than one that is square, because circles can be more securely cut into the door glass. This is because square holes can make glass more vulnerable to cracking when a drill is used on it. This is also a safer option since you don't have to drill into the toughened glass, which could shatter and harm your pet or your family members. This is especially crucial if you have elderly or children living in your home that could be injured by glass fragments.